2630 Symptoms of error in JAF

 You may encounter this error using Jaf box.

Getting MCU ID

MCU ID: 0×3162
FLASH ID0: 883C0020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 11
FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 0
First 16 bytes: AD 7E B6 1B 23 10 03 40 C6 05 E4 01 20 A2 00 00
Checking RAM for ALGO…
Algo is ready…
Checking FAID calculation…
P-key nokia module version 01.02
Done!
Phone Restarted…
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Documents and Settings\czaren\Desktop\Rm-298_2630\rm298__57.20.mcusw
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Documents and Settings\czaren\Desktop\Rm-298_2630\rm298__57.20.mcusw
PPM Flash file: C:\Documents and Settings\czaren\Desktop\Rm-298_2630\rm298__57.20.ppm_ej
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Documents and Settings\czaren\Desktop\Rm-298_2630\rm298__57.20.mcusw
PPM Flash file: C:\Documents and Settings\czaren\Desktop\Rm-298_2630\rm298__57.20.ppm_ej
CNT Flash file: C:\Documents and Settings\czaren\Desktop\Rm-298_2630\rm298__57.20.image__pre_ej
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
MCU: C:\Documents and Settings\czaren\Desktop\Rm-298_2630\rm298__57.20.mcusw
Booting phone…
MCU ID: 0×3162
BOOT file: C:\Program Files\ODEON\JAF\Flash\u3_2nd.fia
Loader version: 04.46.01 -> Revision: 0007
Boot size is 0×09A8
Boot is ready…
FLASH ID0: 883C0020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 11
FLASH ID1: 883C0020 <=> ST -> Type not in database Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 11
First 16 bytes: AD 7E B6 1B 23 10 03 40 C6 05 E4 01 20 A2 00 00
Flash ID is 0×3C882000
Flash loader is C:\Program Files\ODEON\JAF\Flash\u3_intel.fia
Loader version: 04.46.01 -> Revision: 0007
Loader size is 0×5548; Loader chk: fe
Loader is ready…
P-key nokia module version 01.02
MSID: 8497C09880C995B9BF497AF424
MSID decoded: 2C40BAE900096CC7A9000000
FAID: 46D6521B402FD1F3DC8F9A1B
Operation took 0 minutes 10 seconds…
Erasing…
Found 2 interval(s) to erase
Erasing area: 01000000 - 0101FFFF…
Erasing area: 01020000 - 01C3FFFF…
Operation took 1 minutes 50 seconds…
Writing…
Perm. Data Restore OK
Operation took 1 minutes 6 seconds…
Restarting MCU…
CNT: C:\Documents and Settings\czaren\Desktop\Rm-298_2630\rm298__57.20.image__pre_ej
Booting phone…
MCU ID: 0×3162
BOOT file: C:\Program Files\ODEON\JAF\Flash\u3_2nd.fia
Loader version: 04.46.01 -> Revision: 0007
Boot size is 0×09A8
Boot is ready…
FLASH ID0: 883C0020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 11
FLASH ID1: 883C0020 <=> ST -> Type not in database Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 11
First 16 bytes: AD 7E B6 1B 23 10 03 40 C6 05 E4 01 20 A2 00 00
Flash ID is 0×3C882000
File is already converted to 128k page…
Flash loader is C:\Program Files\ODEON\JAF\Flash\u3_intel.fia
Loader version: 04.46.01 -> Revision: 0007
Loader size is 0×5548; Loader chk: fe
Loader is ready…
P-key nokia module version 01.02
MSID: 84747A140168A07C0320F1E989
MSID decoded: D26EBAF100096CC7AA000610
FAID: C84E8B4305AA6896FE906DF6
Operation took 0 minutes 10 seconds…
Erasing Content Pack…
Found 2 interval(s) to erase
Erasing area: 02000000 - 02DBFFFF…
Erasing area: 02DC0000 - 02F9FFFF…
Operation took 4 minutes 37 seconds…
Writing…
Perm. Data Restore OK
Operation took 0 minutes 24 seconds…
Restarting MCU…
Operation took 0 minutes 1 seconds…
Extracting Content Pack…
CP Extract Failed!
PPM: C:\Documents and Settings\czaren\Desktop\Rm-298_2630\rm298__57.20.ppm_ej
Booting phone…
FAILED ->jaf configuration 2
FAILED ->jaf configuration 1
MCU ID: 0xFBE6
This MCU ID is not supported in chosen flash file…
Error booting phone…

You may rely on my log to identify the problem.

It means that this is not a SW problem.

Just reheat or reball the UEM.

For your Info..

Nokia bb5 flash error identification with jaf

1)Booting phone...APE Boot Data:Asic ID: 17100701Asic Mode ID: 00Asic Public ID: 0263DAC3902CB3B1AB83BEF8E79FA987E4E68FECHASH: 2C05369F57CC3C4CF9E783E83D9B512B00000000ROM ID: AB5E4ADB27A06946

CMT Boot Data:Asic ID: 000000010000022600010006000C192101002200Asic Mode ID: 00Asic EM ID: 00000352Asic Public ID: 12200202F57251519FE05B4ECE928FA7AB0B5330HASH: E9EFF4BFAA5393217CA6B17755FC3E1400000000ROM ID: F28A211FCEA7B19DCMT Boot File: C:Program FilesODEONJAFFlashrap3gv2_2nd.fgLoader version: 01.15.00 -> Revision: 0000Patching CMT boot step2…CMT Boot ReadyCMT Flash ID: 225000EC <=> SAMSUNG (SEC) -> K8S6415ETBCMT Flash Data: 00000000000000000000000000000000CMT Loader: C:Program FilesODEONJAFFlashRAP3Gv3_algo.fgLoader version: 01.21.01 -> Revision: 0000CMT Loader ReadyAPE Boot: C:Program FilesODEONJAFFlashhelen3_2nd.fgLoader version: 01.23.00 -> Revision: 0000Patching APE boot step2…APE Boot ReadyError in cmd read id…Error in ape get id…

Q)why show this error with 5 pin cable
Answer) VBUS POWER DET OR RX2 CONNECTION MISSING TIME SHOW THIS ERROR
Solution)change cable

Q)7 pin cable show this same error?
Aswer)POWER DET OR RX2 not proper
solution)clean flash interface,check TAHVO or RETU
MAINLY THIS CAUSE TAHVO problem

Booting phone...APE Boot Data:Asic ID: 17100701Asic Mode ID: 00Asic Public ID: 8D8000D96997B019C64F82E50D6E7E56F062074AHASH: 2C05369F57CC3C4CF9E783E83D9B512B00000000ROM ID: AB5E4ADB27A06946

CMT Boot Data:Asic ID: 000000010000022600010006000C192101002200Asic Mode ID: 00Asic EM ID: 00000353Asic Public ID: 0FD0000651755D51E258231DB9B10843FA32F8C0HASH: E9EFF4BFAA5393217CA6B17755FC3E1400000000ROM ID: F28A211FCEA7B19DCMT Boot File: C:Program FilesODEONJAFFlashrap3gv2_2nd.fgLoader version: 01.15.00 -> Revision: 0000Patching CMT boot step2…CMT Boot ReadyCMT Flash ID: 00000000 <=> Flash -> not detectedCMT Flash Data: NOT AVAILABLECMT Loader: C:Program FilesODEONJAFFlashRAP3Gv3_algo.fgLoader version: 01.21.01 -> Revision: 0000Error loading cmt loader…

THIS CAUSE CMT FLASH IC PROBLEM
SOLUTION REFLOW OR REBALL CMT FLASH IC

Booting phone...APE Boot Data:Asic ID: 17100701Asic Mode ID: 00Asic Public ID: C57A6C30A60BFE52D39FC1751D66A629FB40EB4EHASH: 2C05369F57CC3C4CF9E783E83D9B512B00000000ROM ID: AB5E4ADB27A06946CMT Boot Data:Asic ID: 000000010000022600010006000C192101002200Asic Mode ID: 00Asic EM ID: 00000353Asic Public ID: 1E80000999865A516630285C29EAFDD6F54AA796HASH: E9EFF4BFAA5393217CA6B17755FC3E1400000000ROM ID: F28A211FCEA7B19DCMT Boot File: C:Program FilesODEONJAFFlashrap3gv2_2nd.fgLoader version: 01.15.00 -> Revision: 0000Patching CMT boot step2…CMT Boot ReadyCMT Flash ID: 225000EC <=> SAMSUNG (SEC) -> K8S6415ETBCMT Flash Data: 00000000000000000000000000000000CMT Loader: C:Program FilesODEONJAFFlashRAP3Gv3_algo.fgLoader version: 01.21.01 -> Revision: 0000error loading cmt loader……

THIS CAUSE FIRST CHECK VDRAM VOLT1.8 THIS VOLT GRENERATED BY RETU
RETU DAMAGED TIME SHOW THIS ERROR
THEN FIRST CHECK OR REBALL RETU
SECOND STEP CHECK RAP OR RAM

MCU Flash file: C:Program FilesNokiaPhoenixProductsRM-84RM84_50737301.C0PPM Flash file: C:Program FilesNokiaPhoenixProductsRM-84RM84_50737301.V11CNT Flash file: NONEAPE Variant file: ?Manual mode selected, version can’t be checked!Booting phone…CMT Boot Data:Asic ID: 000000010000022600010006000C192101002200Asic Mode ID: 00Asic EM ID: 00000352Asic Public ID: 0C800103D8654E5160FC20C285A16EB1C330C054HASH: E9EFF4BFAA5393217CA6B17755FC3E1400000000ROM ID: F28A211FCEA7B19DCMT Boot File: C:Program FilesODEONJAFFlashrap3gv2_2nd.fgLoader version: 01.15.00 -> Revision: 0000Patching CMT boot step2…CMT Boot ReadyCMT Flash ID: 225000EC <=> SAMSUNG (SEC) -> K8S6415ETBCMT Flash Data: 00000000000000000000000000000000CMT Loader: C:Program FilesODEONJAFFlashRAP3Gv3_algo.fgLoader version: 01.21.01 -> Revision: 0000CMT Loader ReadyOperation took 0 minutes 6 seconds…Sending CNF Data…APE blocks present in flash file but no APE mcu detected in phone. Aborting!

THIS CAUSE APE FLASH(COMBO MEMORY) NOT DETECTED
FIRST CHECK APE DRIVER
SECOND CHECK OR REFLOW COMBO MEMORY
THIRD CHECK OMAP
RETU OR TAHVO CHANCE ONLY 10% __________________

Asic ID: 17100708Asic Mode ID: 00Asic Public ID: 7D751C1A33A273258CAB80EEAB7C0F532993E3A8HASH: 49A97E826B93BA20B7ED0B082475C00500000000ROM ID: 1DFD66132C872FD4

CMT Boot Data:Asic ID: 000000010000022600010006010C192101003000Asic Mode ID: 00Asic EM ID: 00000B22Asic Public ID: 07D00114FA576350088F1A62AEF357F6BDF4D82AHASH: BAF3A9C3DBFA8454937DB77F2B8852B100000000ROM ID: 273F6D55DFAAF68FCMT Boot File: C:Program FilesODEONJAFFlashrap3gv3_2nd.fgLoader version: 01.1E.00 -> Revision: 0000Patching CMT boot step1…Patching CMT boot step2…Patching CMT boot step3…CMT Boot ReadyCMT Flash ID: 22E800EC <=> SAMSUNG (SEC) -> K5G2829ATCCMT Flash Data: 00000000000000000000000000000000CMT Loader: C:Program FilesODEONJAFFlashRAP3Gv3_algo.fgLoader version: 01.21.01 -> Revision: 0000Patching CMT loader step1…Patching CMT loader step3…CMT Loader ReadyAPE Boot: C:Program FilesODEONJAFFlashhelen3_2nd.fgLoader version: 01.23.00 -> Revision: 0000Patching APE boot step1…Patching APE boot step2…Patching APE boot step3…Error loading ape boot…

 THIS CAUSE 75%CABLE PROBLEM

Booting phone...APE Boot Data:Asic ID: 17100701Asic Mode ID: 00Asic Public ID: 244320733BC5907FDCB71FCE53140F088146DB83HASH: 2C05369F57CC3C4CF9E783E83D9B512B00000000ROM ID: AB5E4ADB27A06946

CMT Boot Data:Asic ID: 000000010000022600010006000C192101002200Asic Mode ID: 00Asic EM ID: 00000341Asic Public ID: 07C0000B15CB4F5737D6CA662765741F8B61B672HASH: E9EFF4BFAA5393217CA6B17755FC3E1400000000ROM ID: F28A211FCEA7B19DCMT Boot File: C:Program FilesODEONJAFFlashrap3gv2_2nd.fgLoader version: 01.15.00 -> Revision: 0000Patching CMT boot step2…CMT Boot ReadyCMT Flash ID: 22FA00EC <=> SAMSUNG (SEC) -> K8S6415ETACMT Flash Data: 00000000000000000000000000000000CMT Loader: C:Program FilesODEONJAFFlashRAP3Gv3_algo.fgLoader version: 01.21.01 -> Revision: 0000CMT Loader ReadyAPE Boot: C:Program FilesODEONJAFFlashhelen3_2nd.fgLoader version: 01.23.00 -> Revision: 0000Patching APE boot step2…APE Boot ReadyNo flash ids reported…Error in ape get id…

THIS CAUSE 80%FLASH IC PROBLEM
REBALL OR CHANGE FLASH IC

CMT Boot Data:Asic ID: 000000010000022600010006010C192101001101Asic Mode ID: 00Asic EM ID: 00000353Asic Public ID: 19600010B2336B565F226B0477C67F55A1886761HASH: BAF3A9C3DBFA8454937DB77F2B8852B100000000ROM ID: 191EC665DFAAF68FCMT Boot File: C:Program FilesODEONJAFFlashrap3gv3_2nd.fgLoader version: 01.1E.00 -> Revision: 0000Patching CMT boot step1…Patching CMT boot step2…Patching CMT boot step3…CMT Boot ReadyCMT Flash ID: 22FE00EC <=> SAMSUNG (SEC) -> K8S5615ETACMT Flash Data: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFCMT Loader: C:Program FilesODEONJAFFlashRAP3Gv3_algo.fgLoader version: 01.21.01 -> Revision: 0000Patching CMT loader step1…Patching CMT loader step3…CMT Loader ReadyDone!Restarting phone…Done!

THIS CAUSE MAINLY CABLE PROBLEM 5 PIN CABLE USED TIME PHONE NOT ENTER NORMAL MODE MEANS SEE THIS CMT Flash DataFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF MUST USED 7 PIN CABLE PROBLEM 100%SOLVED

Booting phone...

CMT Boot Data:Asic ID: 000000010000022600010006010C192101001101Asic Mode ID: 00Asic EM ID: 00000353Asic Public ID: 30700107CB8A7E5654E497A533FA3E3F90458DEBHASH: BAF3A9C3DBFA8454937DB77F2B8852B100000000ROM ID: 191EC665DFAAF68FCMT Boot File: C:Program FilesODEONJAFFlashUFSrap3gv3_2nd.fgLoader version: 01.10.02 -> Revision: 0000Patching CMT boot step1…Patching CMT boot step2…Patching CMT boot step3…CMT Boot ReadyCMT Flash ID: 89810089 <=> INTEL -> Type not in databaseCMT Flash Data: 10000000000000000000000000000000CMT Loader: C:Program FilesODEONJAFFlashUFSRAP3Gv3_algo_fps8.fgLoader version: 01.0C.05 -> Revision: 0000Patching CMT loader step1…Patching CMT loader step3…CMT Loader ReadyOperation took 0 minutes 6 seconds…Sending CRT data…Error in RD cmd…Error preparing flashing…

75% CMT FLASH IC PROBLEM
Solution—REBALL FLASH IC

 Init usb communication…
PRESS POWER ON NOW!
Searching for phone…Found
Sending RAW loader…
Using 06.02.002
Elf2flash 02.33.000 RAW loader…
Patching RAW boot step1…
Patching RAW boot step3…
Sending RAW Loader…
……………….Loader Sent!
Stage 2 starting…………………………………… …………………..Loader Sent!
Stage 3 starting………………Phone prepared OK!
Waiting for the phone to boot…

FLASH IC DAMAGED TIME USB Flashing Failed Show This Error
But TAHVO DAMAGED TIME SHOW THIS SAME ERROR

6120 white to blackscreen

Symptoms:

Upon switching On,it shows whitescreen in a seconds and it booted immediately in black or bluescreen.

If you put to box with cable (e.g. JAF) it shows Local Mode

If you put a charger it boot in normal situation.

Here is the log in JAF box:

CMT Boot Data:
25:06:2009  21:50 -> Asic ID: 25:06:2009  21:50 -> 000000010000022600010006010C192101003000
25:06:2009  21:50 -> Asic Mode ID: 25:06:2009  21:50 -> 00
25:06:2009  21:50 -> Asic EM ID: 25:06:2009  21:50 -> 00000B22
25:06:2009  21:50 -> Asic Public ID: 25:06:2009  21:50 -> 1B50000678A101542D6A37FED3210F3C41AA0FBE
25:06:2009  21:50 -> HASH: 25:06:2009  21:50 -> BAF3A9C3DBFA8454937DB77F2B8852B100000000
25:06:2009  21:50 -> ROM ID: 25:06:2009  21:50 -> 273F6D55DFAAF68F
25:06:2009  21:50 -> CMT Boot File: C:\Program Files\ODEON\JAF\Flash\rap3gv3_2nd.fg
25:06:2009  21:50 -> Loader version: 01.1E.0025:06:2009  21:50 ->  -> Revision: 0000
25:06:2009  21:50 -> Patching CMT boot step1…
25:06:2009  21:50 -> Patching CMT boot step2…
25:06:2009  21:50 -> Patching CMT boot step3…
25:06:2009  21:50 -> CMT Boot Ready
25:06:2009  21:50 -> CMT Flash ID: 25:06:2009  21:50 -> 22E800EC25:06:2009  21:50 ->  <=> SAMSUNG (SEC) -> K5G2829ATC
25:06:2009  21:50 -> CMT Flash Data: 25:06:2009  21:50 -> 00000000000000000000000000000000
25:06:2009  21:50 -> CMT Loader: C:\Program Files\ODEON\JAF\Flash\RAP3Gv3_algo.fg
25:06:2009  21:50 -> Loader version: 01.21.0125:06:2009  21:50 ->  -> Revision: 0000
25:06:2009  21:50 -> Patching CMT loader step1…
25:06:2009  21:50 -> Patching CMT loader step3…
25:06:2009  21:50 -> CMT Loader Ready
25:06:2009  21:50 -> APE Boot: C:\Program Files\ODEON\JAF\Flash\helen3_2nd.fg
25:06:2009  21:50 -> Loader version: 01.23.0025:06:2009  21:50 ->  -> Revision: 0000
25:06:2009  21:50 -> Patching APE boot step1…
25:06:2009  21:50 -> Patching APE boot step2…
25:06:2009  21:50 -> Patching APE boot step3…
25:06:2009  21:50 -> APE Boot Ready
25:06:2009  21:50 -> APE Flash ID: 25:06:2009  21:50 -> 00A100EC25:06:2009  21:50 ->  <=> SAMSUNG (SEC) -> K5E1G12ACM
25:06:2009  21:50 -> APE Flash Data: 25:06:2009  21:50 -> FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
25:06:2009  21:50 -> Done!

Use this firmware through MCU patching only.

http://w1.uploadmb.com/dw.php?id=1246037223

Most of the technician think this is a HW problem.before you do it,flash this firmware first.

Goodluck!

2680s Contact Service

First guys, never directly go in HW.

Check first using your box like JAf,

here is my logs:

Symptoms:

Detected PKEY: 90017ECC
25:06:2009  20:02 -> Card life counter: 93.02%
25:06:2009  20:02 -> P-key nokia module version 01.02
25:06:2009  20:02 -> Detected JAF INTERFACE version: 01.B1, Driver version: 40000, Library version: 30107
25:06:2009  20:02 -> JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
25:06:2009  20:02 -> JAF DCT4/BB5 PRODUCT DIR: C:\Program Files\Nokia\Phoenix\Products\
25:06:2009  20:02 -> JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
25:06:2009  20:02 -> JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
25:06:2009  20:02 -> USB Cable Driver version: 7.1.16.0
25:06:2009  20:02 -> 25:06:2009  20:02 -> Getting MCU ID
25:06:2009  20:02 ->
MCU ID: 0×3162
25:06:2009  20:02 -> FLASH ID0: 883C0020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 11
25:06:2009  20:02 -> FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 0
25:06:2009  20:02 -> First 16 bytes: 25:06:2009  20:02 -> AD 7E B6 1B 00 FF 10 40 00 00 00 00 00 00 00 00
25:06:2009  20:02 -> Checking RAM for ALGO…
25:06:2009  20:03 -> Algo is ready…
25:06:2009  20:03 -> Checking FAID calculation…
25:06:2009  20:03 -> P-key nokia module version 01.02
25:06:2009  20:03 -> Done!
Phone Restarted…
25:06:2009  20:03 -> FILES SET FOR FLASHING:
25:06:2009  20:03 -> MCU Flash file: NONE
25:06:2009  20:03 -> PPM Flash file: NONE
25:06:2009  20:03 -> CNT Flash file: NONE
25:06:2009  20:03 -> ADSP Flash file: NONE
25:06:2009  20:03 -> APE Variant file: NONE
25:06:2009  20:03 -> APE User Flash file: NONE
25:06:2009  20:03 -> Switching to serial…
25:06:2009  20:03 -> Powering the phone…
25:06:2009  20:03 -> Reading…
25:06:2009  20:03 -> MCU SW version: V 04.91
03-09-08
RM-392
(c) Nokia            
25:06:2009  20:03 -> HW version: 1000
25:06:2009  20:03 -> PCI version:
25:06:2009  20:03 -> UEM version: 4386
25:06:2009  20:03 -> UPP version: 12642
25:06:2009  20:03 -> RFIC version: 0500
25:06:2009  20:03 -> DSP version: ICPR72_08w27_UPP
25:06:2009  20:03 -> LCD version: SEIKO
25:06:2009  20:03 -> PPM version: V 04.91
03-09-08
RM-392
(c) Nokia            
IA
25:06:2009  20:03 -> Content Pack version: Content: ia
V 04.91
03-09-08
RM-392
(c) Nokia            

25:06:2009  20:03 -> Production serial number: HEA133034
25:06:2009  20:03 -> Product code: 0565094
25:06:2009  20:03 -> Module code: 0203726
25:06:2009  20:03 -> Basic production code: 0556744
25:06:2009  20:03 -> Flash code:
25:06:2009  20:03 -> Order number:
25:06:2009  20:03 -> Product specific data:
25:06:2009  20:03 -> Long production SN: 0
25:06:2009  20:03 -> ATO:
25:06:2009  20:03 -> Default SN type:
25:06:2009  20:03 -> IMEI plain: 356390028699093
25:06:2009  20:03 -> IMEI spare to net: 3A 65 93 00 82 96 09 09
25:06:2009  20:03 -> IMEI SV to net: 33 65 93 00 82 96 09 19 F6
25:06:2009  20:03 -> Master Code: 5143505754
25:06:2009  20:03 -> Failed reading simlock data…
25:06:2009  20:03 -> Phone type: RM-392, Software version: 04.91, 25:06:2009  20:03 -> Language Pack: IA
25:06:2009  20:03 -> User code: 12345
25:06:2009  20:03 ->

If you encounter something like this, it’s a cable problem (check contacts)

 Detected PKEY: 90017ECC
25:06:2009  21:55 -> Card life counter: 91.75%
25:06:2009  21:55 -> P-key nokia module version 01.02
25:06:2009  21:55 -> Detected JAF INTERFACE version: 01.B1, Driver version: 40000, Library version: 30107
25:06:2009  21:55 -> JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
25:06:2009  21:55 -> JAF DCT4/BB5 PRODUCT DIR: C:\Program Files\Nokia\Phoenix\Products\
25:06:2009  21:55 -> JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
25:06:2009  21:55 -> JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
25:06:2009  21:55 -> USB Cable Driver version: 7.1.16.0
25:06:2009  21:55 -> 25:06:2009  21:55 -> Getting MCU ID
25:06:2009  21:55 ->
MCU ID: 0×2031
25:06:2009  21:55 -> FLASH ID0: 88260020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 10
25:06:2009  21:55 -> FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 0
25:06:2009  21:55 -> First 16 bytes: 25:06:2009  21:55 -> AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
25:06:2009  21:55 -> Checking RAM for ALGO…
25:06:2009  21:55 -> Algo is ready…
25:06:2009  21:55 -> Checking FAID calculation…
25:06:2009  21:55 -> P-key nokia module version 01.02
25:06:2009  21:55 -> Done!
Phone Restarted…
25:06:2009  21:55 -> Backing up PM Field 208 as RPL…
25:06:2009  21:55 -> Setting local mode…
25:06:2009  21:56 -> Failed! Aborting!
25:06:2009  21:56 -> Failed to backup imei…
25:06:2009  21:56 -> Powering the phone…
25:06:2009  21:57 -> Failed! Aborting!
25:06:2009  21:57 -> 25:06:2009  21:57 -> Getting MCU ID
25:06:2009  21:57 ->
MCU ID: 0×2031
25:06:2009  21:57 -> FLASH ID0: 88260020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 10
25:06:2009  21:57 -> FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 0
25:06:2009  21:57 -> First 16 bytes: 25:06:2009  21:57 -> AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
25:06:2009  21:57 -> Checking RAM for ALGO…
25:06:2009  21:57 -> Algo is ready…
25:06:2009  21:57 -> Checking FAID calculation…
25:06:2009  21:57 -> P-key nokia module version 01.02
25:06:2009  21:57 -> Done!
Phone Restarted…
25:06:2009  21:57 -> FILES SET FOR FLASHING:
25:06:2009  21:57 -> MCU Flash file: NONE
25:06:2009  21:57 -> PPM Flash file: NONE
25:06:2009  21:57 -> CNT Flash file: NONE
25:06:2009  21:57 -> ADSP Flash file: NONE
25:06:2009  21:57 -> APE Variant file: NONE
25:06:2009  21:57 -> APE User Flash file: NONE
25:06:2009  21:59 -> Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-74\
25:06:2009  21:59 ->
25:06:2009  21:59 -> Searching for default location of ini…
25:06:2009  21:59 -> Checking path: C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-74\
25:06:2009  21:59 -> Searching for JAF saved location of ini…
25:06:2009  21:59 -> Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-74\
25:06:2009  21:59 -> No ini files found…
25:06:2009  21:59 -> FILES SET FOR FLASHING:
25:06:2009  21:59 -> MCU Flash file: NONE
25:06:2009  21:59 -> PPM Flash file: NONE
25:06:2009  21:59 -> CNT Flash file: NONE
25:06:2009  21:59 -> ADSP Flash file: NONE
25:06:2009  21:59 -> APE Variant file: NONE
25:06:2009  21:59 -> APE User Flash file: NONE
25:06:2009  21:59 -> FILES SET FOR FLASHING:
25:06:2009  21:59 -> MCU Flash file: NONE
25:06:2009  21:59 -> PPM Flash file: NONE
25:06:2009  21:59 -> CNT Flash file: NONE
25:06:2009  21:59 -> ADSP Flash file: NONE
25:06:2009  21:59 -> APE Variant file: NONE
25:06:2009  21:59 -> APE User Flash file: NONE
25:06:2009  21:59 -> Phone Type:
25:06:2009  22:00 -> FILES SET FOR FLASHING:
25:06:2009  22:00 -> MCU Flash file: NONE
25:06:2009  22:00 -> PPM Flash file: NONE
25:06:2009  22:00 -> CNT Flash file: NONE
25:06:2009  22:00 -> ADSP Flash file: NONE
25:06:2009  22:00 -> APE Variant file: NONE
25:06:2009  22:00 -> APE User Flash file: NONE
25:06:2009  22:04 -> JAF version 1.98.63
Detected PKEY: 90017ECC
25:06:2009  22:04 -> Card life counter: 91.48%
25:06:2009  22:04 -> P-key nokia module version 01.02
25:06:2009  22:04 -> Detected JAF INTERFACE version: 01.B1, Driver version: 40000, Library version: 30107
25:06:2009  22:04 -> JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
25:06:2009  22:04 -> JAF DCT4/BB5 PRODUCT DIR: C:\Program Files\Nokia\Phoenix\Products\
25:06:2009  22:04 -> JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
25:06:2009  22:04 -> JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
25:06:2009  22:04 -> USB Cable Driver version: 7.1.16.0
25:06:2009  22:04 -> 25:06:2009  22:04 -> Getting MCU ID
25:06:2009  22:04 ->
MCU ID: 0×2031
25:06:2009  22:05 -> FLASH ID0: 88260020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 10
25:06:2009  22:05 -> FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 0
25:06:2009  22:05 -> First 16 bytes: 25:06:2009  22:05 -> AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
25:06:2009  22:05 -> Checking RAM for ALGO…
25:06:2009  22:05 -> Algo is ready…
25:06:2009  22:05 -> Checking FAID calculation…
25:06:2009  22:05 -> P-key nokia module version 01.02
25:06:2009  22:05 -> Done!
Phone Restarted…
25:06:2009  22:05 -> FILES SET FOR FLASHING:
25:06:2009  22:05 -> MCU Flash file: NONE
25:06:2009  22:05 -> PPM Flash file: NONE
25:06:2009  22:05 -> CNT Flash file: NONE
25:06:2009  22:05 -> ADSP Flash file: NONE
25:06:2009  22:05 -> APE Variant file: NONE
25:06:2009  22:05 -> APE User Flash file: NONE
25:06:2009  22:05 -> Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-74\
25:06:2009  22:05 -> Scanning for ini files…
25:06:2009  22:05 -> INI file .ini is missing. Continue searching for second ini type…
25:06:2009  22:05 -> Changing flashing settings…
25:06:2009  22:05 -> FILES SET FOR FLASHING:
25:06:2009  22:05 -> MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.300
25:06:2009  22:05 -> PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30l
25:06:2009  22:05 -> CNT Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30.image_ctv_za
25:06:2009  22:05 -> ADSP Flash file: NONE
25:06:2009  22:05 -> APE Variant file: NONE
25:06:2009  22:05 -> APE User Flash file: NONE
25:06:2009  22:05 -> Languages in ppm: English,French,Afrikaans,Swahili,Zulu,Sesotho,Xhosa
25:06:2009  22:05 -> Changing flashing settings…
25:06:2009  22:05 -> FILES SET FOR FLASHING:
25:06:2009  22:05 -> MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.300
25:06:2009  22:05 -> PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30g
25:06:2009  22:05 -> CNT Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30.image_g
25:06:2009  22:05 -> ADSP Flash file: NONE
25:06:2009  22:05 -> APE Variant file: NONE
25:06:2009  22:05 -> APE User Flash file: NONE
25:06:2009  22:05 -> Languages in ppm: English,French,German,Spanish,Arabic,Urdu,Farsi
25:06:2009  22:05 -> MCU: 25:06:2009  22:05 -> C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30025:06:2009  22:05 ->
25:06:2009  22:05 -> Booting phone…
25:06:2009  22:05 -> MCU ID: 0×2031
25:06:2009  22:05 -> BOOT file: C:\Program Files\ODEON\JAF\Flash\u_2nd.fia
25:06:2009  22:05 -> Loader version: 04.46.0125:06:2009  22:05 ->  -> Revision: 0007
25:06:2009  22:05 -> Boot size is 0×09A0
25:06:2009  22:05 -> Boot is ready…
25:06:2009  22:05 -> FLASH ID0: 88260020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 10
25:06:2009  22:05 -> FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 0
25:06:2009  22:05 -> First 16 bytes: 25:06:2009  22:05 -> AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
25:06:2009  22:05 -> Flash ID is 0×26882000
25:06:2009  22:05 -> Flash loader is C:\Program Files\ODEON\JAF\Flash\u_st_i.fia
25:06:2009  22:05 -> Loader version: 04.46.0125:06:2009  22:05 ->  -> Revision: 0007
25:06:2009  22:05 -> Loader size is 0×4B28; Loader chk: 35
25:06:2009  22:05 -> Loader is ready…
25:06:2009  22:05 -> P-key nokia module version 01.02
25:06:2009  22:05 -> MSID: 84AC6CBDA18924D374C0F220E8
25:06:2009  22:05 -> MSID decoded: 5E42BAE900154B3EAA000000
25:06:2009  22:05 -> FAID: F12A94BE1191BCE62F2D4434
25:06:2009  22:05 -> Operation took 0 minutes 15 seconds…
25:06:2009  22:05 -> Erasing…
25:06:2009  22:05 -> Found 3 interval(s) to erase
25:06:2009  22:05 -> Erasing area: 01000000 - 0101FFFF…
25:06:2009  22:06 -> Erasing area: 01020000 - 017BFFFF…
25:06:2009  22:07 -> Erasing area: 01F20000 - 01FDFFFF…
25:06:2009  22:07 -> Operation took 1 minutes 12 seconds…
25:06:2009  22:07 -> Writing…
25:06:2009  22:07 -> Perm. Data Restore OK
25:06:2009  22:07 -> Operation took 0 minutes 42 seconds…
25:06:2009  22:07 -> Restarting MCU…
25:06:2009  22:07 -> CNT: 25:06:2009  22:07 -> C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30.image_g25:06:2009  22:07 ->
25:06:2009  22:07 -> Booting phone…
25:06:2009  22:07 -> MCU ID: 0×2031
25:06:2009  22:07 -> BOOT file: C:\Program Files\ODEON\JAF\Flash\u_2nd.fia
25:06:2009  22:07 -> Loader version: 04.46.0125:06:2009  22:07 ->  -> Revision: 0007
25:06:2009  22:07 -> Boot size is 0×09A0
25:06:2009  22:07 -> Boot is ready…
25:06:2009  22:07 -> FLASH ID0: 88260020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 10
25:06:2009  22:07 -> FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 0
25:06:2009  22:07 -> First 16 bytes: 25:06:2009  22:07 -> AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
25:06:2009  22:07 -> Flash ID is 0×26882000
25:06:2009  22:07 -> Flash loader is C:\Program Files\ODEON\JAF\Flash\u_st_i.fia
25:06:2009  22:07 -> Loader version: 04.46.0125:06:2009  22:07 ->  -> Revision: 0007
25:06:2009  22:07 -> Loader size is 0×4B28; Loader chk: 35
25:06:2009  22:07 -> Loader is ready…
25:06:2009  22:08 -> P-key nokia module version 01.02
25:06:2009  22:08 -> MSID: 84071A601BC5CD79FB90CAB7D8
25:06:2009  22:08 -> MSID decoded: 1C15BAE300154B3EAD0005BD
25:06:2009  22:08 -> FAID: 6C052C0D56785C8F3E7A804D
25:06:2009  22:08 -> Operation took 0 minutes 10 seconds…
25:06:2009  22:08 -> Erasing Content Pack…
25:06:2009  22:08 -> Found 1 interval(s) to erase
25:06:2009  22:08 -> Erasing area: 01C00000 - 01F1FFFF…
25:06:2009  22:08 -> Operation took 0 minutes 25 seconds…
25:06:2009  22:08 -> Writing…
25:06:2009  22:08 -> Perm. Data Restore OK
25:06:2009  22:08 -> Operation took 0 minutes 5 seconds…
25:06:2009  22:08 -> Restarting MCU…
25:06:2009  22:08 -> Operation took 0 minutes 1 seconds…
25:06:2009  22:08 -> Extracting Content Pack…
25:06:2009  22:08 -> Running: (c) Nokia File Server
25:06:2009  22:08 -> CNT Extract Skiped.
25:06:2009  22:08 -> Operation took 0 minutes 1 seconds…
25:06:2009  22:08 -> PPM: 25:06:2009  22:08 -> C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30g25:06:2009  22:08 ->
25:06:2009  22:08 -> Booting phone…
25:06:2009  22:08 -> Phone didn’t answer with TX line low after UEM reset!
Causes:
1. put a 27-33 pico capacitor in connector b/w mbus-gnd.
2. UEM damaged -> replace uem.
25:06:2009  22:08 -> MCU ID: 0xDDDD
25:06:2009  22:08 -> This MCU ID is not supported in chosen flash file…
25:06:2009  22:08 -> Error booting phone…
25:06:2009  22:09 -> Changing mode…
25:06:2009  22:10 -> Failed!!!
25:06:2009  22:11 -> FAILED
25:06:2009  22:12 -> 25:06:2009  22:12 -> Getting MCU ID
25:06:2009  22:13 -> Failed! Aborting!
25:06:2009  22:13 -> Done!
Phone Restarted…

Even if you write PM for this situation it still the same.So follow the below instructions.

Solution taken:

 Just make unlock and choose the right MCU file:

  Detected PKEY: 90017ECC
25:06:2009  22:17 -> Card life counter: 91.04%
25:06:2009  22:17 -> P-key nokia module version 01.02
25:06:2009  22:17 -> Detected JAF INTERFACE version: 01.B1, Driver version: 40000, Library version: 30107
25:06:2009  22:17 -> JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
25:06:2009  22:17 -> JAF DCT4/BB5 PRODUCT DIR: C:\Program Files\Nokia\Phoenix\Products\
25:06:2009  22:17 -> JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
25:06:2009  22:17 -> JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
25:06:2009  22:17 -> USB Cable Driver version: 7.1.16.0
25:06:2009  22:18 -> 25:06:2009  22:18 -> Getting MCU ID
25:06:2009  22:18 ->
MCU ID: 0×2031
25:06:2009  22:18 -> FLASH ID0: 88260020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 10
25:06:2009  22:18 -> FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 0
25:06:2009  22:18 -> First 16 bytes: 25:06:2009  22:18 -> AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
25:06:2009  22:18 -> Checking RAM for ALGO…
25:06:2009  22:18 -> Algo is ready…
25:06:2009  22:18 -> Checking FAID calculation…
25:06:2009  22:18 -> P-key nokia module version 01.02
25:06:2009  22:18 -> Done!
Phone Restarted…
25:06:2009  22:18 -> FILES SET FOR FLASHING:
25:06:2009  22:18 -> MCU Flash file: NONE
25:06:2009  22:18 -> PPM Flash file: NONE
25:06:2009  22:18 -> CNT Flash file: NONE
25:06:2009  22:18 -> ADSP Flash file: NONE
25:06:2009  22:18 -> APE Variant file: NONE
25:06:2009  22:18 -> APE User Flash file: NONE
25:06:2009  22:19 -> Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-74\
25:06:2009  22:19 -> Scanning for ini files…
25:06:2009  22:19 -> INI file .ini is missing. Continue searching for second ini type…
25:06:2009  22:19 -> Changing flashing settings…
25:06:2009  22:19 -> FILES SET FOR FLASHING:
25:06:2009  22:19 -> MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.300
25:06:2009  22:19 -> PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30l
25:06:2009  22:19 -> CNT Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30.image_ctv_za
25:06:2009  22:19 -> ADSP Flash file: NONE
25:06:2009  22:19 -> APE Variant file: NONE
25:06:2009  22:19 -> APE User Flash file: NONE
25:06:2009  22:19 -> Languages in ppm: English,French,Afrikaans,Swahili,Zulu,Sesotho,Xhosa
25:06:2009  22:19 -> Changing flashing settings…
25:06:2009  22:19 -> FILES SET FOR FLASHING:
25:06:2009  22:19 -> MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.300
25:06:2009  22:19 -> PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30f
25:06:2009  22:19 -> CNT Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30.image_f
25:06:2009  22:19 -> ADSP Flash file: NONE
25:06:2009  22:19 -> APE Variant file: NONE
25:06:2009  22:19 -> APE User Flash file: NONE
25:06:2009  22:19 -> Languages in ppm: English,German,Hebrew,Arabic,Russian
25:06:2009  22:19 -> MCU: 25:06:2009  22:19 -> C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30025:06:2009  22:19 ->
25:06:2009  22:19 -> Booting phone…
25:06:2009  22:19 -> MCU ID: 0×2031
25:06:2009  22:19 -> BOOT file: C:\Program Files\ODEON\JAF\Flash\u_2nd.fia
25:06:2009  22:19 -> Loader version: 04.46.0125:06:2009  22:19 ->  -> Revision: 0007
25:06:2009  22:19 -> Boot size is 0×09A0
25:06:2009  22:19 -> Boot is ready…
25:06:2009  22:19 -> FLASH ID0: 88260020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 10
25:06:2009  22:19 -> FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 0
25:06:2009  22:19 -> First 16 bytes: 25:06:2009  22:19 -> AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
25:06:2009  22:19 -> Flash ID is 0×26882000
25:06:2009  22:19 -> Flash loader is C:\Program Files\ODEON\JAF\Flash\u_st_i.fia
25:06:2009  22:19 -> Loader version: 04.46.0125:06:2009  22:19 ->  -> Revision: 0007
25:06:2009  22:19 -> Loader size is 0×4B28; Loader chk: 35
25:06:2009  22:19 -> Loader is ready…
25:06:2009  22:19 -> P-key nokia module version 01.02
25:06:2009  22:19 -> MSID: 84AC6CBDA18924D374C0F220E8
25:06:2009  22:19 -> MSID decoded: 5E42BAE900154B3EAA000000
25:06:2009  22:19 -> FAID: F12A94BE1191BCE62F2D4434
25:06:2009  22:19 -> Operation took 0 minutes 9 seconds…
25:06:2009  22:19 -> Erasing…
25:06:2009  22:19 -> Found 3 interval(s) to erase
25:06:2009  22:19 -> Erasing area: 01000000 - 0101FFFF…
25:06:2009  22:19 -> Erasing area: 01020000 - 017BFFFF…
25:06:2009  22:20 -> Erasing area: 01F20000 - 01FDFFFF…
25:06:2009  22:20 -> Operation took 1 minutes 12 seconds…
25:06:2009  22:20 -> Writing…
25:06:2009  22:21 -> Perm. Data Restore OK
25:06:2009  22:21 -> Operation took 0 minutes 41 seconds…
25:06:2009  22:21 -> Restarting MCU…
25:06:2009  22:21 -> CNT: 25:06:2009  22:21 -> C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30.image_f25:06:2009  22:21 ->
25:06:2009  22:21 -> Booting phone…
25:06:2009  22:21 -> MCU ID: 0×2031
25:06:2009  22:21 -> BOOT file: C:\Program Files\ODEON\JAF\Flash\u_2nd.fia
25:06:2009  22:21 -> Loader version: 04.46.0125:06:2009  22:21 ->  -> Revision: 0007
25:06:2009  22:21 -> Boot size is 0×09A0
25:06:2009  22:21 -> Boot is ready…
25:06:2009  22:21 -> FLASH ID0: 88260020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 10
25:06:2009  22:21 -> FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 0
25:06:2009  22:21 -> First 16 bytes: 25:06:2009  22:21 -> AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
25:06:2009  22:21 -> Flash ID is 0×26882000
25:06:2009  22:21 -> Flash loader is C:\Program Files\ODEON\JAF\Flash\u_st_i.fia
25:06:2009  22:21 -> Loader version: 04.46.0125:06:2009  22:21 ->  -> Revision: 0007
25:06:2009  22:21 -> Loader size is 0×4B28; Loader chk: 35
25:06:2009  22:21 -> Loader is ready…
25:06:2009  22:21 -> P-key nokia module version 01.02
25:06:2009  22:21 -> MSID: 84071A601BC5CD79FB90CAB7D8
25:06:2009  22:21 -> MSID decoded: 1C15BAE300154B3EAD0005BD
25:06:2009  22:21 -> FAID: 6C052C0D56785C8F3E7A804D
25:06:2009  22:21 -> Operation took 0 minutes 10 seconds…
25:06:2009  22:21 -> Erasing Content Pack…
25:06:2009  22:21 -> Found 1 interval(s) to erase
25:06:2009  22:21 -> Erasing area: 01C00000 - 01F1FFFF…
25:06:2009  22:21 -> Operation took 0 minutes 25 seconds…
25:06:2009  22:21 -> Writing…
25:06:2009  22:21 -> Perm. Data Restore OK
25:06:2009  22:21 -> Operation took 0 minutes 5 seconds…
25:06:2009  22:21 -> Restarting MCU…
25:06:2009  22:21 -> Operation took 0 minutes 0 seconds…
25:06:2009  22:22 -> Extracting Content Pack…
25:06:2009  22:22 -> Running: (c) Nokia File Server
25:06:2009  22:22 -> CNT Extract Skiped.
25:06:2009  22:22 -> Operation took 0 minutes 1 seconds…
25:06:2009  22:22 -> PPM: 25:06:2009  22:22 -> C:\Program Files\Nokia\Phoenix\Products\RM-74\rm74__5.30f25:06:2009  22:22 ->
25:06:2009  22:22 -> Booting phone…
25:06:2009  22:22 -> MCU ID: 0×2031
25:06:2009  22:22 -> BOOT file: C:\Program Files\ODEON\JAF\Flash\u_2nd.fia
25:06:2009  22:22 -> Loader version: 04.46.0125:06:2009  22:22 ->  -> Revision: 0007
25:06:2009  22:22 -> Boot size is 0×09A0
25:06:2009  22:22 -> Boot is ready…
25:06:2009  22:22 -> FLASH ID0: 88260020 <=> ST -> Type not in database Addr0: 0×01000000 - 0×01FFFFFF, SectorSize0: 10
25:06:2009  22:22 -> FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0×02000000 - 0×02FFFFFF, SectorSize1: 0
25:06:2009  22:22 -> First 16 bytes: 25:06:2009  22:22 -> AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
25:06:2009  22:22 -> Flash ID is 0×26882000
25:06:2009  22:22 -> Flash loader is C:\Program Files\ODEON\JAF\Flash\u_st_i.fia
25:06:2009  22:22 -> Loader version: 04.46.0125:06:2009  22:22 ->  -> Revision: 0007
25:06:2009  22:22 -> Loader size is 0×4B28; Loader chk: d5
25:06:2009  22:22 -> Loader is ready…
25:06:2009  22:22 -> P-key nokia module version 01.02
25:06:2009  22:22 -> MSID: 84D7E8944201E66AE59EDFA578
25:06:2009  22:22 -> MSID decoded: 3E4EBAE900154B3EA8000000
25:06:2009  22:22 -> FAID: 14C33269AAA656E440A7D74B
25:06:2009  22:22 -> Operation took 0 minutes 10 seconds…
25:06:2009  22:22 -> Erasing PPM…
25:06:2009  22:22 -> Found 1 interval(s) to erase
25:06:2009  22:22 -> Erasing area: 017C0000 - 01BFFFFF…
25:06:2009  22:22 -> Operation took 0 minutes 35 seconds…
25:06:2009  22:22 -> Writing…
25:06:2009  22:23 -> Perm. Data Restore OK
25:06:2009  22:23 -> Operation took 0 minutes 8 seconds…
25:06:2009  22:23 -> Restarting MCU…
25:06:2009  22:23 -> Flashing Done!
25:06:2009  22:23 -> Operation took 3 minutes 51 seconds…
25:06:2009  22:23 ->
25:06:2009  22:23 -> After flash processing…
25:06:2009  22:23 -> Waiting for phone to boot…
25:06:2009  22:23 -> Reading…
25:06:2009  22:23 -> Phone type: RM-74, Software version: 5.30
25:06:2009  22:23 -> IMEI: 357597004527820
25:06:2009  22:23 -> Product Code: 0527775
25:06:2009  22:23 -> Resetting PPC…
25:06:2009  22:23 -> Setting FULL FACTORY……25:06:2009  22:23 -> Setting test mode…
25:06:2009  22:23 -> Setting FULL FACTORY…
25:06:2009  22:23 -> Operation took 0 minutes 4 seconds…
25:06:2009  22:23 -> Done!
25:06:2009  22:23 -> Done!
25:06:2009  22:23 -> Done!

JAF Tutorial & Definitions

Flash files to download and install
example:

RM-38_v 11.00 (mcusw 4.14) Emea Apac China LTA
this called major version, must be installed first before you can install minor version.
contains MCU, PPM, and CNT.

RM-38_v 11.01 (mcusw 4.14) Emea Apac China LTA
called minor version, can be installed after major version installed, usually contains only PPM and CNT (no MCU, but for some other type, maybe contains MCU newer version also)

another example:
RM-36_v 8.00 (mcusw 5.050407) Euro
for EURO countries

RM-36_v 9.00 (mcusw 5.050440) Apac
for Asia Pacific countries

================================================== ==============

DCT4 tab

Flash settings tab

MCU : Micro Control Unit

PPM : Post Programming Memory, contains language

CNT : Content Pack, contains tones, games, etc

ADSP : Advance Digital Signal Processor, flash file for DSP chips

APE : Application Processor Engine

Use INI :
When you thick this, software will detect phone connected type, and “Use INI” files setting when exist in “Product Directory” for choosing flash files.
INI : (*.ini)
This file contains flash files setting for each “Product Code”, including MCU, PPM, CNT, PP (Product Profile), etc.
(Even in 3250, different product code may have different MCU to be flashed).
These files are extracted from firmware/data package that we have installed.
Use this option in order to avoid choosing wrong flash files, example :
- If you don’t know for sure which MCU, PPM, or CNT.
- Choose right PPM for language that you want
- How to choose right CNT that suitable with your PPM
After a Product Code has been chosen automatically, you can change it manually with other Product Code that you want to flash.

Run INI :
After flashing completed, software will upload also Product Profile according INI that has been chosen and flashed.

Product Profile :
This file contains customization for each Product Code, example : GPRS settings, WAP bookmarks, etc..
For Communicator Phone, this file also contains keyboard layout.

Load NFP:
NFP: Nokia File Protected
Data package (MCU, PPM, and CNT) for nokia CDMA phone was compressed as a file :
*.NFP, and it is protected by password.
Thick this option, choose *.NFP, software will extracted it automatically as MCU, PPM, and CNT.

Easy Cable :
It’s a special cable, suitable with pop-up connector for few type phone, ex : 1600, which can be use for flashing. Thick this if you use this kind of cable.

RPL 208 :
PM field number 208 was copied from DATA1/ IMEI flash data.
Software will back up this area as RPL(DATA1 only), that useful for recover flash IMEI if something happen after flash (IMEI ????), or you changed flash IC, you no need to change UEM also if you have back up for this phone. Some type don’t have this field, like 1100, 2300, etc. Make sure your phone can enter Local Mode for this option.

FTD ON:
FTD : Field Test Display / Net Monitor : special menu for DCT4 and DCT4 TIKU that can be activated with flashing, it contains many feature for testing phone and network.

Product Code :
Every Nokia phone has 7digit number that written in the back sticker.
This Product Code will differ phone that sold to one country and another, also phone that sold with customization for an operator, will have different Product Code also.
This number also saved somewhere in PM area.
Thick “Change Product Code” will change Product Code number in PM area after flashing completed.

Factory Set :
Reset all settings to factory default after flash completed.

Manual Flash:
this option will disable software detect the phone model and open his folder when you click on “MCU”, “PPM”, etc, or thick on “Use INI”

Warranty :
When you press *#warranty# or *#92702689#, phone will display some hidden information like Serial Number, Made, etc, including “Life Timer”.
This option after flash will reset “Life Timer” back to zero after flashed.

Unlock:
Initialize sim lock after flash

SKIP tab :

Skip Erase :
normally, software will erase first some area according Flash Files needed before writing them. If you thick this option, without erase first, software will write the Flash Files that have been chosen. Use this option only if you already have fully erased the phone manually.

Skip AFP :
AFP : After Flash Processing
After flashing completed, software will try to put the phone into Local Mode and read some info about it. This option will disable that process.
Use this only if you know why this process should be skip, example you flash an Erase File that make the phone dead/ fully erase.
Not all Erase File erase whole part of flash IC, some Erase File only erase some part of flash IC and phone still alives.

Skip MCU ID :
MCU ID is UPP (Universal Phone Processor) recognition, inside flash file, there’s recognition for MCU ID that supported (by that flash file).
Use this option only if you sure that you flash the phone with right flash file, but software give warning that MCU ID is not supported by flash file that have you choose.
Note : usually warning about MCU ID is not supported but right Flash Files has been chosen is caused by bad cable connection. Try restart software, reconnect F-Bus cable from phone, and try again.
For dead phone suspected / possibility hardware problem, if MCU flashing has been completed, continue flashing with PPM only usually will solve.

BT :
Bluetooth IC have own firmware including in MCU file.
You may skip this if you flash the phone with same version, this will save flashing time a little.
But you have to skip this if BT IC is damage, it’s indicated with when you flash a phone and software error in the middle with warning : “Error loading additional loader..”

Operations Tab :

INF : INFO
Make sure your phone can enter Local or Test mode for this operation.
At the end of this operation, software will detect phone’s Product Code and load Flash Files according it.
If no suitable product code found, you must thick “Manual Flash” and then “Use INI”,software will ask you to “Select Phone Model”.
You can sort it by “Type” or by “Name”, or you can type phone code like RH-12, and all “INI” settings for this phone will be loaded, and can be chosen.
Note : if you don’t find your phone type or name in the list, but you have Data Package installed for this phone, open “jaf_nok4models.ini” with Notepad and add it like this

[RM-307]
De******ion=Nokia 2505

and save this file.

CHK : Check
Will check phone hardware condition like
- Relation between UEM (Universal Energy Management - power IC) and UPP (Universal Phone Processor)
- MCU ID / UPP
- Flash IC
- RAM IC
- First 16 bytes
- FAID Calculation
Remember, bad F-Bus cable also make this operation failed !!!

Service:
This button related with “Service Operations” tab

Erase Flash:
Software will try to back up RPL 208 if your phone can enter Local Mode or IMEI Flash Data not corrupted, or RP 208 exist, and then check phone hardware like MCU ID, etc and display Erase Flash Manager.

Flash Chip List:
Below this tab you can choose which IC that you want to erase, and you can modify Erase Address.
Start Address always 0×000000 and End Address always 0xxFFFFF, depends on Flash IC size.

FULL Erase :
Full Erase will erase all Flash IC, including PM (Permanent Memory), & will make SIM Lock Data corrupted.
Make sure that you have back up PM to be uploaded after flash and unlock after this operation.
Click Start Erase to execute this operation.

PM : Permanent Memory, an area in flash IC that wasn’t reached by flash files, means normal flashing shouldn’t change it’s value.
It contains data of RF, EM, Product Code, Security Code, and so many more.
For some type it also contains backup IMEI Flash Data, even phone book and gallery content.

PM file can be opened with Notepad or Wordpad.
PM area indicates with :
Field Number 0 - xxx (some type has field numbers <200, some has <255, but newer phone type may have 300>).
Each “Field Number” may has sub “Record Number”
Field Number indicates with : [x]
And Record Number indicates with : x=

If you fully erase a phone, you can upload PM that you have read from another phone which same type, but make sure you have deleted field 5, 120, and 208 from it, ’caused it contains IMEI data.

Repair BT / Repair Bluetooth :
Same with erase PM field 4 index 17 (4:17) that contains BT address.
Some type of Nokia phone save BT address in this field, if this area corrupt or filled with another BT address (maybe caused by upload PM from another phone), & BT can not be switch on, try use this option.

Read Fls ….

Prod Dir :
Change default Flash File detection from C:\Program Files\Nokia\Phoenix to another.

FLASH : start flashing

(Un)Lock:
this button related with “Unlock settings” tab

Init simlock : Initialize SIM Lock, remove Operator SIM Lock restriction

Write SIM file : write file *.SIM that contains SIM Lock settings.

Code Calculator : calculate codes from IMEI number, network code, and ASIC code, for initialize SIM Lock, enter it with type the codes manually with keypad

Read Codes : read phone for IMEI and calculate code for initialize SIM Lock

Auto Lock: after this operation, phone will recognize network code from first SIM Card that inserted to phone, and lock to this network.

Autolock IMSI :
IMSI : International Mobile Subscriber Identity, after this operation, phone will recognize first SIM Card that inserted and lock phone to this SIM.

Lock to Network: enter the network code manually and phone will be lock to this network

Load JAVA :
Upload JAVA application to the phone

MMC Rst:
with special cable adapter, this will reset locked Memory Card

Make INI:
If you have chosen your flash file manually or USE INI, this operation will create your own “INI file” for that type. After this, software will automatically load that flash files after INF pressed.

IMEI tool:

There are 2 IMEI in DCT4 phone:
First is in UEM, also called DATA2, OTP (one time programmable).
Second in flash IC, also called DATA1, not OTP.
If DATA1 get corrupted or not synchronize with DATA2, Watchdog timer will be enabled, phone will be restart after +/- 30 seconds. You will see software says IMEI ?????????

Make ASK: make “ask” file to be calculated become RPL.
This operation is used after you change UEM and want same IMEI number with your phone previously (IMEI at back cover sticker), or you have change flash IC but don’t have back up for this.
Thick “UEM Changed” in order to get DATA2 calculation also,
otherwise ASK will be calculated only for Flash IC / DATA1.

Write RPL (reply) :
Because there are 2 IMEI in DCT4 phone, RPL may contains DATA1 only or DATA1 & DATA2. You can open it with Notepad/Wordpad.
RPL from back up RPL 208 contains only DATA1, will be uploaded to flash IC.
RPL from ASK calculation can be contains 2 data (remember about thick “UEM changed” when make ASK), one will be uploaded to flash IC : DATA1, and the other one will be uploaded to UEM: DATA2.
If you changed UEM, DATA2 will be wrote and become OTP IMEI. No problem if RPL contains 2 data but you did not change UEM, as long as DATA1 and DATA2 are synchronized, phone will be normal.

ASIC : Application Specific Integrated Circuit
class of DCT4 phone,
ASIC 2
ASIC 5 - WD2
ASIC 6 - TIKU BT
ASIC 7
ASIC 11

If you changed UEM and do not want to calculated RPL, you can use “free supplied rpl” that come with software installation, but you have to write RPL with same ASIC to your phone.

IMEI Patch:
this will “patched” IMEI Plain, IMEI that showed by pressing *#06#, with desired IMEI that you want. Patch options only work for DCT4 ASIC2.
And this only work for normal phone, means patch WILL NOT SOLVE problem IMEI ????????? that ’caused by DATA1 corrupted.
If you try this with phone that have problem IMEI ?????????, Watchdog timer will be enabled, and your phone will restart after +/- 30 seconds.

IMEI Save: back up PM 208 as RPL

Unlock : Initialize SIM Lock , needed after write RPL

Read UEM : Read UEM IMEI
If you have phone with IMEI ?????????, check also whether UEM IMEI still good.
If yes, read ASK, calculate ASK to RPL, and write RPL.
But if UEM IMEI also damage, you have to Change UEM.

Service Operations tab: (use Service button to execute)
Make sure you phone able to enter local and test mode for this service.
If not, check the cable or maybe phone have hardware problem.

Read, Write, and erase PM : look above about PM.

Self Test : test some phone conditions via software.
Always use this feature if your phone has “Contact Service” problem that can not be solve with erasing and flashing.

Disp Test : LCD test.

Upload TUN : RF value for CDMA phone was saved with file named *.tun.

Factory Setting: reset the phone to factory settings

Prod. Manager :
Read or change/write some value that saved in PM area:
- Product code
- HW version : Hardware Version : please be careful edit this for RM-72 - 6230i, ’cause PPM and CNT flash file was different between old and new HW version.
- Order Number
- Production SN
- Manufacture Month : in phone showed by typing *#warranty#

File System Format:
Format User Area of the phone, user data will be lost.
Remember that WD2 have different File System with DCT4 TIKU as example.
WD2 = Symbian EPOC, Drive for User Area : C
DCT4 TIKU : FILE2 , use Format Type : Low Level Format, and type : NAND

So, if software can not detect File System correctly, try making Full Factory before execute this again.

User Code Edit:
Read Security Code which saved at PM filed number 35.

Upload and Read PP:
please look above “Product Profile”

ADC Read :
Analog to Digital Converter : some Self Test about phone battery, charger, etc

Fun Explorer :
About exploring JAVA application in DCT4 phone.

Warranty Reset :
look above about Warranty.

Phone Mode:
(?) read phone status
change phone mode to
Local Mode
Test Mode
Normal Mode

Communication Mode:
F-Bus cable : flasher cable
USB: DKU-2/CA-53, when you connect DCT4 TIKU with this cable, you will be able to make some operation like : make Full factory, Init SIM Lock, etc, but not for flashing.

——————————————————————–

Flashing DCT4 APE phone : 9300, 9500, and 7710:
connect both F-Bus cable and USB cable (DKU-2 CA-53) to phone.
when you make CHK for this phone, System Tray in Windows will give warning about “USB DEVICE NOT RECOGNIZE”, this is normal, and this must be happen.
If you don’t get this warning, you need to check again USB connection to phone, otherwise phone may have hardware problem.
During flashing process windows will install drivers needed for flashing this phone.

================================================== =================

BB5 tab

BB5 phone :
BB : Base Band
Single chip : have only CMT processor. example : 6270, 62880, etc
Dual chip : have two processor, CMT (cellular Mobile telephone) and APE (Application Processor Engine) example : 6630, 6680, N70, etc.

Communication Mode:
F-BUS cable : use only 7 pins cable for flashing with JAF box.
Make sure your phone can enter Local or Test Mode !!!
If not, maybe you need to check your cable, and then modified it, if not suitable with JAF specification.
1. NEVER EVER try putting 9v battery in F-BUS cable though your cable has this connector !!!
2. Resistance between BSI-GND must be 68k ohms, if less than it, maybe you will find “error sync the phone when make “CHK”
3. Resistance in BSI serial must be 5,1k(5k1) or 7,5k(7k5) ohms. Otherwise your phone can not enter Local / Test Mode.
4. Make sure VPP line from RJ45 connected to RX2 in phone.
Never use cable that connected VPP line in RJ45 with VPP in phone, you will get error something like “Error APE get id”

I don’t give explanation about P-KEY and UFS Box, because newer BB5 phone with RAPIDO processor doesn’t supported by UFS Box.

USB : all (alive) BB5 phone supported by USB flashing, you may use DKU-2 or CA-53, but some types needs DKE-2/mini USB for this operation. make sure your battery fully charged, or charge it with an original charger before start flashing.
When you flash phone and software give error warning “error getting flash id”,
put sim card inside, do not select offline mode, and flash the phone.
Note : make sure you disable all connection in PC Suite (if you installed Nokia PC Suite software in your PC) when using this service.

Dead USB :
Few types of BB5 with single chips supported by “Dead USB flashing”.
Choose flash file manually, connect USB cable to phone, and when software give command to “press the power now”, press switch on/off briefly. In windows systems try, will show “Nokia USB ROM”, and windows will install the driver automatically.

For some types, successfully dead USB flashing will revive the phone, but gallery content will be empty, so you need to flash again with USB as normally.

Downgrade :
This option based on Dejan’s trick to be able to flash a working/normal BB5 phone with lower version.
Maybe not all BB5 supported by this option. So, if you try downgrade and the phone become dead, flash again with latest/highest firmware version.

CRT 308:
PM field number 308 contains SIM Lock data, make sure your phone can enter Local Mode before flash, in order to make successful back up.
If something wrong after flashing process and SIM Lock Data become corrupted, use Write PM and choose this back up to be written to the phone. Your sim lock state will back like before flashing.

CRT BKP: Certificate Back Up, saved as *.RPL.

Skip APE: skip APE flashing.

SX4 Authority :
BB5 phones have protection for writing RF(1 ) and Energy(309, 0×135 in hex) settings in EPROM. Not having those settings in phone, is known as ‘Contact Retailer Problem’, or ‘Security Error’ in Self Test. In order to write those settings phone requires an authorization that only SX4 Smart Card can perform.
As those cards are hard to get, software can use server support for this authorization.
To authorize, connect BB5 phone, and power it on.
Press “SX4 AUTH”. If you have SX4 card connected to PC, software will use it to compute the authorization password and send it to phone.
If you don’t have card, software will connect to server to compute authorization password.
If this process have sucessfuly done, Write PM to the phone without field number 308.

================================================== =============

Card Life Counter :
this will decrease every time you flash a phone, if yourCard Life Counter almost empty / almost 0%, go to P-KEY tab and press Update P-KEY to make it full again / 100%.
This operation need internet connection, & make sure you have disabled your firewall.

Update Loaders:
FIA = Flash Identification Address are files that needed for flashing, to identify MCU ID and Flash Files which suitable with phones. If you press this, software will check whether new version from support site exist and replace your flash loaders with new one if you download it.

================================================== =============

VBat - Battery Voltage
BSI - Battery size Indicator
GND - Ground, conductive mass